RS485, Modbus & NVT

api.rs485Send(msg)

Overview

Sends msg to RS485 bus.

Turn on RS485 using rs485State first.

Arguments

• msg (string) - Data to be sent to RS485 bus

Example

--sends 'test' string to RS485
api.rs485Send('test')

api.rs485Setup(arg1, arg2, ...)

Overview

Change the configuration of RS485 interface.

Arguments

• arg1 - "RX_BUFFER" (string) - set/get size of receive buffer
• arg2 - value (integer)(optional) - set size of the receive buffer

or

• arg1 - baudrate (integer) - Baudrate to use for communication (up to 921600 baud)
• arg2 - parity (integer) - Parity, 0 for none, 1 for odd and 2 for even parity
• arg3 - stopBits (integer) - Number of stop bits, 1 or 2 allowed
• arg4 - dataBits (integer) - Number of data bits, 7 or 8 allowed

Example

--setup RS485 interface to 9600 Baud, 8E1
api.rs485Setup(9600, 2, 1, 8)

api.rs485State(state)

Overview

Turns on the RS485 circuitry.

Must be used before rs485Send or rs485Receive.

Arguments

• state (integer) - New state of RS485 circuitry: 0 for off, 1 for on (fast power-up)

Example

api.rs485State(0) --turn off RS485

api.rs485Receive(timeout,arg1,arg2)

Overview

Waits timeout milliseconds for data reception from RS485 bus.

Turn on RS485 using rs485State() function first.

After the first character is received the inter-character (i.e. inter-byte timeout) delay is 10ms. This can be changed by giving a integer number to arg1.

Arguments

• timeout (integer) - The maximum time in milliseconds to wait for RS485 device answer
• arg1 (optional) - If string is entered here, it's used as terminator (can be more than one character), otherwise it's inter-byte timeout
• arg2 (optional) - If arg1 is used as inter-byte timeout, this is used to define terminator string (can be more than one character)

Return

• answer (string) - Data received from RS485 bus in given time
• len (integer) - Number of bytes received

Example

--waits 1s for answer from RS485 bus
ans,len = api.rs485Receive(1000)

--waits 1s for answer from RS485 bus and gets everything until it finds "!" character
--stop garbage collector so it doesn't limit the memory (higher speed, prevent's loosing characters at 9600bd)
collectgarbage("stop")
ans,len = api.rs485Receive(1000,"!")
--restart the garbage collector (the memory will overflow, without it)
collectgarbage("restart")

api.modbusCrc(msg)

Overview

Calculates Modbus request checksum.

Arguments

• msg (string) - Modbus request

Return

• crc (string) - Modbus crc for request

Example

--calculate checksum for Modbus request 110100010002
req = pack.pack('<b6', 0x11,0x01,0x00,0x01,0x00,0x02)
crc = api.modbusCrc(req) --crc = "EE9B"

api.modbusRTU(address, registerAddr, functionCode, typeSpec, registerCount, timeout, retry, interByteTimeout, ignoreCRC)

Overview

The api.modbusRTU() function is used to communicate with a modbus device over a serial connection using the RTU (Remote Terminal Unit) protocol. It can be used to read or write one or more registers of various data types. The function takes several parameters, including the modbus device address, the starting register address, the function code, the type specification of the register(s), the number of registers to read or write, and several timeout and retry parameters.

The typeSpec parameter is a Lua string that specifies the data type of the register(s) being read or written. It uses the Lua Packing and Unpacking syntax to specify the type and formatting of the data. For example, to read a single 16-bit unsigned integer, the typeSpec parameter would be "H".

The function returns the value(s) read from or written to the modbus register(s), according to the specified typeSpec. For example, if typeSpec is "H" and registerCount is 2, the function would return two 16-bit unsigned integers.

If the function fails to communicate with the modbus device, it will retry the operation according to the retry parameter. If the operation still fails after the specified number of retries, the function will return nil.

Arguments

• address(integer) - The address of the modbus device to communicate with.
• registerAddr(integer) - The starting address of the modbus register to read or write.
• functionCode(integer) - The modbus function code to use for the operation (e.g. read coils, read input registers, write multiple coils, etc.).
• typeSpec(string) - A Lua string that specifies the data type of the register(s) being read or written. More details here.
  • if the typeSpec is "", it returns data as received
• registerCount(integer) - The number of registers to read or write.
• timeout(integer) - The timeout (in milliseconds) for the modbus communication operation.
• retry(integer) - The number of times to retry the operation if it fails.
• interByteTimeout(integer) - The timeout (in milliseconds) between receiving bytes during the modbus communication operation.
• ignoreCRC(bool)(optional) - in case this is true, function is not checking modbus CRC.

Return

The function returns the value(s) read from the modbus register(s), according to the specified typeSpec.

Example

--setup the RS485 and turn on the RS485 module
api.rs485Setup(9600,2,1,8) api.rs485State(1)
--read 0x4003 register (modbus ID in case of INEPRO PRO1)
x=api.modbusRTU(10,0x4003,3,">h",1,2000,3,10) print(x)

api.nvtProcess(buf)

Overview

Processes NVT message and either sets baudrate, datasize, parity or stop size for MBUS or MODBUS.

Arguments

• buf (string) - Message to be processed

Return

• msg (string) - Message without NVT sequence
• answer (string) - NVT answer

Example

-- If massage received (buf) send it to RS485
ret,port,buf = api.loraSend(0,1000,data)
if buf ~= nil then
	buf, nvtans = api.nvtProcess(buf)
	api.rs485Send(buf)
end

api.nvtEncode(msg)

Overview

Encodes message to NVT format

Arguments

• msg (string) - Message to be encoded to NVT

Return

• answer (string) - NVT message

Example

ans,len = api.rs485Receive(50)
ans = api.nvtEncode(ans)
api.loraSend(0,1,ans)